Ressources

Consultez nos ressources gratuites.

Contactez-nous
Industrial facility with large overhead metal pipes supported by red metal framework under a clear blue sky.

Guides techniques

Tetra a publié une série de guides, disponibles à la commande.

Cover of the HRSG Inspection Planning Guide (2nd Edition)

HRSG Inspection Planning Guide (2nd Edition)

L'inspection fait partie de la maintenance courante de toute chaudière de récupération (HRSG). Des inspections visuelles sont réalisées à intervalles réguliers, conformément aux exigences des organismes de réglementation et des assureurs.

Cover of the HRSG Tube Failure Diagnostic Guide (3rd Edition)

HRSG Tube Failure Diagnostic Guide (3rd Edition)

Les tubes des chaudières de récupération (HRSG) permettent d'extraire l'énergie utile de la chaleur des gaz d'échappement des turbines à gaz dans les centrales à cycle combiné, ou de la chaleur produite par les flux de procédé dans les installations pétrochimiques.

Livres blancs techniques

Une sélection de documents techniques à consulter.

Merci ! Votre demande a bien été reçue.
Oups ! Une erreur s'est produite lors de l'envoi du formulaire.

Défaillances de tubes liées à la chimie de l'eau

La plupart des défaillances de tubes dues à la corrosion ont une composante directement liée à la chimie de l'eau.

En savoir plus

Conservation côté eau

La principale raison de choisir la conservation humide est que le délai de redémarrage de la chaudière est bien plus court qu'après une conservation à sec.

En savoir plus

Défaillances de tubes liées à la conservation

L'oxygène est un contaminant courant de l'eau de chaudière, particulièrement corrosif pour l'acier au carbone.

En savoir plus

Préservation des HRSG

La préservation des circuits eau et vapeur du HRSG pendant les périodes d'arrêt est un objectif important pour toute centrale.

En savoir plus

Brûleurs de post-combustion

L'excès d'air dans les fumées de la turbine à gaz permet de brûler du combustible supplémentaire par post-combustion dans le HRSG.

En savoir plus

Conservation côté fumées

La corrosion côté fumées se produit pendant les arrêts. Elle est maximale dans les faisceaux de la partie froide en raison de la présence de dépôts acides.

En savoir plus
Tetra Engineering logo. Orange triangular pyramid on a black background.Tetra Engineering logo. Orange triangular pyramid on a black background.

Nous contacter

Pour discuter de la manière dont nous pouvons vous aider à améliorer les performances de votre centrale ou à préserver sa valeur dans le temps

Nous contacter

Publications, présentations et articles

Une sélection de publications, présentations et articles issus des grandes conférences et événements du secteur.

Titre
Auteur
HRSG Preservation During Shutdowns: A Key Issue Often Neglected
HRSG Preservation During Shutdowns: A Key Issue Often NeglectedHRSG Preservation During Shutdowns: A Key Issue Often Neglected
Misha Gadher & James Malloy
Modern Power Systems, 2026
What do HRSG tube failure statistics tell us?
What do HRSG tube failure statistics tell us?What do HRSG tube failure statistics tell us?
Misha Gadher & Mark Taylor
Modern Power Systems
Counterfeit, Fraudulent and Suspect Items (CFSI) – Steel and HRSGs
Counterfeit, Fraudulent and Suspect Items (CFSI) – Steel and HRSGsCounterfeit, Fraudulent and Suspect Items (CFSI) – Steel and HRSGs
Taylor M.
IMechE HRSG User Group 2022
Adapting Existing Thermal Desalination Plants to Produce Hydrogen
Adapting Existing Thermal Desalination Plants to Produce HydrogenAdapting Existing Thermal Desalination Plants to Produce Hydrogen
Malloy J.
2022 World Utilities Congress
Root Cause Failure Investigation of MSCV Drain Failures
Root Cause Failure Investigation of MSCV Drain FailuresRoot Cause Failure Investigation of MSCV Drain Failures
P. Jackson, A. Wholey, E. Tsai and D. Burns
ASME 2022 Pressure Vessels & Piping Conference

Projets réalisés

Forte de plus de 35 ans d'expérience dans les services liés à la production d'électricité et de vapeur industrielle, Tetra Engineering a mené de très nombreux projets.

Asia

Boiler Tube Failure Root Cause Analysis, 2017

After several tube failures in recent years in the 1st row of LTRH hanger tubes, Tetra was tasked with performing a Root Cause Analysis (RCA) to determine the underlying cause of the failures. A detailed review of operating data, failure reports and design information was carried out and potential causes investigated. The tube failure mechanism as determined by metallurgy was short-term overheating, with temperatures likely exceeding 700°C prior to failures. Two contributing causes were identified by elimination of all other possibilities: temporary loss of steam flow in affected leading row tubes coupled with high flue gas temperatures in certain tubes at the side of the boiler gas path.  Unfortunately, the underlying root cause of the loss of flow could not be confirmed, whereas the asymmetric flue gas temperature distribution is a known issue since commissioning.

Middle East

HP Evaporator Tube Failure Analysis, 2016

During a recent condenser tube leak at a CCGT Power Station in the Middle East, two trips occurred on the boiler feedwater pumps leading to trips of one of the HRSGs.  During that time, three tubes failed on the HP Evaporator. Tetra Engineering performed an investigation into the failures with the aim of determining the failure mechanism, to estimate the root cause of failure, and to identify inspection priorities in case damage may have gone undetected. This work included metallurgical analysis and a review of key operating data. Failures were located directly under the risers at extreme ends of the HP Drum. The most probable source of tensile overload is tube quenching when flow restarted

Europe

Attemperator Sleeve Failure Study, 2016

In 2015, it was discovered that the thermal sleeve in the attemperator in a client’s power station hot reheat line had failed, resulting in fracture around the circumferential weld in the sleeve’s mid section. For this reason, Tetra was engaged by the owner to investigate. The investigation showed failure from fatigue cracking. There were no signs of thermal fatigue damage, hence quenching from over-spraying was discounted as the root cause. The cracked area showed signs of high cyclic local strain, and given the moderate number of starts low-cycle fatigue was thought to be the root cause. Differential thermal expansion between the Grade 22 sleeve and the Grade 91 pipe, combined with lock-in of the sleeve on the pin locations, would raise sufficiently high stresses

Europe

HP Bypass Finite Element Analysis, 2015

Tetra was engaged by a client to perform a finite element analysis of the HP Bypass valve reducer, using measured displacements as input. Results from a strain gauge/displacement survey showed a large strain effect occurring during the start-up of the boiler. Initially, both the left and right side strain gauges on the reducer showed compressive strain. During the start something triggered the reducer to experience tensile strain that differed in its intensity between left and right. The purpose of the study was to try to simulate the observed strain fields and determine the root cause.

Tetra Engineering logo. Orange triangular pyramid on a black background.Tetra Engineering logo. Orange triangular pyramid on a black background.

Nous contacter

Pour discuter de la manière dont nous pouvons vous aider à améliorer les performances de votre centrale ou à préserver sa valeur dans le temps

Nous contacter