Ressources

Consultez nos ressources gratuites.

Contactez-nous
Industrial facility with large overhead metal pipes supported by red metal framework under a clear blue sky.

Guides techniques

Tetra a publié une série de guides, disponibles à la commande.

Cover of the HRSG Inspection Planning Guide (2nd Edition)

HRSG Inspection Planning Guide (2nd Edition)

L'inspection fait partie de la maintenance courante de toute chaudière de récupération (HRSG). Des inspections visuelles sont réalisées à intervalles réguliers, conformément aux exigences des organismes de réglementation et des assureurs.

Cover of the HRSG Tube Failure Diagnostic Guide (3rd Edition)

HRSG Tube Failure Diagnostic Guide (3rd Edition)

Les tubes des chaudières de récupération (HRSG) permettent d'extraire l'énergie utile de la chaleur des gaz d'échappement des turbines à gaz dans les centrales à cycle combiné, ou de la chaleur produite par les flux de procédé dans les installations pétrochimiques.

Livres blancs techniques

Une sélection de documents techniques à consulter.

Merci ! Votre demande a bien été reçue.
Oups ! Une erreur s'est produite lors de l'envoi du formulaire.

Classification du fluage de l'acier Grade 91

L'acier Grade 91 surpasse de nombreux autres matériaux industriels par sa résistance accrue à plusieurs modes d'endommagement, dont le fluage.

En savoir plus

Tuyauteries de chaudières de centrale

Les exigences de conception des tuyauteries de chaudière relèvent de deux périmètres, interne et externe.

En savoir plus

Traitement thermique après soudage (PWHT)

Principes du traitement thermique après soudage (PWHT), règles générales de l'ASME Section I (PW-39) et méthode pour déterminer si un PWHT est nécessaire.

En savoir plus

Descriptif de mode opératoire de soudage (DMOS / WPS)

Avant toute opération de soudage, le soudeur et l'ingénieur contrôle qualité doivent connaître parfaitement le contenu du descriptif de mode opératoire de soudage (DMOS).

En savoir plus

Chimie de l'eau dans les HRSG

L'environnement à l'intérieur des tubes de HRSG est un facteur important pour préserver leur intégrité.

En savoir plus

Planification des inspections de HRSG

Élaborer un bon plan d'inspection du HRSG implique plusieurs étapes, de la fixation du calendrier à la revue post-inspection.

En savoir plus
Tetra Engineering logo. Orange triangular pyramid on a black background.Tetra Engineering logo. Orange triangular pyramid on a black background.

Nous contacter

Pour discuter de la manière dont nous pouvons vous aider à améliorer les performances de votre centrale ou à préserver sa valeur dans le temps

Nous contacter

Publications, présentations et articles

Une sélection de publications, présentations et articles issus des grandes conférences et événements du secteur.

Titre
Auteur
Root Cause Failure Analysis of Superheater Tubes Using Computational Fluid Dynamics.
Root Cause Failure Analysis of Superheater Tubes Using Computational Fluid Dynamics.Root Cause Failure Analysis of Superheater Tubes Using Computational Fluid Dynamics.
Fabricius A., Moelling D., Rusaas J.
PowerGen Asia Conference Proceedings, Seoul, South Korea, September, 2016.
Premature Grade 91 failures: Worldwide Plant Operational Experiences
Premature Grade 91 failures: Worldwide Plant Operational ExperiencesPremature Grade 91 failures: Worldwide Plant Operational Experiences
Fabricius A., Jackson P.
Journal of Engineering Failure Analysis, August 2016, Volume 66, Pages 398-406
Understanding Variations in Flow-Accelerated Corrosion Wear Rates in HRSG Evaporator Tubes
Understanding Variations in Flow-Accelerated Corrosion Wear Rates in HRSG Evaporator TubesUnderstanding Variations in Flow-Accelerated Corrosion Wear Rates in HRSG Evaporator Tubes
Malloy J., Rusaas J., Taylor M.
International Conference on Flow Accelerated Corrosion, EdF, France, 2016. // Power Plant Chemistry Magazine, 2017.
HRSG Condition Assessments Identify CAPEX, Maintenance Priorities.
HRSG Condition Assessments Identify CAPEX, Maintenance Priorities.HRSG Condition Assessments Identify CAPEX, Maintenance Priorities.
Jackson P., Moelling D.
Power Magazine, April, 2016.
Covered Piping Systems: O&M Programs for CCGT Plants
Covered Piping Systems: O&M Programs for CCGT PlantsCovered Piping Systems: O&M Programs for CCGT Plants
Rosario R.
Power Magazine, April, 2016.

Projets réalisés

Forte de plus de 35 ans d'expérience dans les services liés à la production d'électricité et de vapeur industrielle, Tetra Engineering a mené de très nombreux projets.

Middle East

CFD Analysis of Cooling Water Outfall - Foam & Pulsation Mitigation, 2025

Tetra Engineering and long term partner R&R Consult, investigated severe foam formation and pressure pulsations at the cooling water outfall of a 1,000 MW combined-cycle gas turbine (CCGT) plant. The issue stemmed from cooling water falling freely from a drop shaft, entraining large volumes of air and causing unstable operation. Using advanced transient two-phase CFD modelling (Volume of Fluid), the hydraulic behaviour was simulated and multiple design modifications were tested. The analysis revealed that air entrainment was the root cause of the foam and pulsations. Tetra Engineering implemented a simple yet effective solution: installing baffle blocks immediately downstream of the drop shaft. This reduced air entrainment by 47%, stabilising plant operation with minimal investment. The result: safer, more reliable cooling water discharge and improved operational performance.

Europe

CFD Analysis of Flue Gas Bypass – Root Cause Analysis, 2024

Tetra Engineering partnered with R&R Consult to investigate reduced steam production at a large natural gas-fired power plant. Despite normal operating conditions, the boiler was underperforming. An inspection revealed that hot flue gas was bypassing the boiler tubes, reducing heat transfer efficiency. CFD analysis by R&R Consult showed that 6.3% of the flue gas was flowing along the sides of the boiler and between modules, missing the heat exchange surfaces entirely. This bypass flow was the root cause of the performance loss. Tetra Engineering designed and installed covering plates to redirect the gas through the intended path. The result was improved boiler performance and increased electricity output.

Middle East

CFD Analysis of Condenser Choking – Root Cause Analysis, 2023

Tetra Engineering partnered with R&R Consult to perform a root cause analysis of a condenser tube system experiencing flow choking. The CFD simulation revealed an uneven flow distribution across the tube sheet, with significantly reduced throughput in peripheral tubes. This pattern was linked to variations in the degree of cleaning across different sections of the condenser. The results demonstrated how CFD provides insight into internal flow behavior that is otherwise difficult to assess, making it a powerful tool for diagnosing and resolving persistent operational issues.

Middle East.

CFD Analysis of GRP Piping Caustic Dosing, 2018

Caustic soda is injected into the product water in order to raise the pH as required by the specification. Inspection of GRP piping has often shown large amounts of deposition inside these pipes. Deposition is mostly observed downstream of the injection point of sodium hydroxide and can therefore be attributed to unsuitable chemical injection. Typical injection setups utilise four simple (no nozzle) injection ports at 90° from one another causing ineffective mixing of the flows, leading to the observed precipitation. Tetra performed a CFD analysis of the caustic injection process to investigate the degree of mixing of the two flows and simulate the effects of modifying the volumetric flow rate.

Tetra Engineering logo. Orange triangular pyramid on a black background.Tetra Engineering logo. Orange triangular pyramid on a black background.

Nous contacter

Pour discuter de la manière dont nous pouvons vous aider à améliorer les performances de votre centrale ou à préserver sa valeur dans le temps

Nous contacter